Errata - English

In Vitamin A, Method 3/Analysis: Change
C_S = concentration of retinyl acetate (C₂₃H₃₂O₂) from USP Vitamin A RS in the Standard solution (μg/mL)
to:
C_S = concentration of retinyl acetate (C₂₂H₃₂O₂) from USP Vitamin A RS in the Standard solution (μg/mL)

In Vitamin A, Method 3/Analysis: Change
C_S = concentration of retinyl acetate (C₂₃H₃₂O₂) from USP Vitamin A RS in the Standard solution (μg/mL)
to:
C_S = concentration of retinyl acetate (C₂₂H₃₂O₂) from USP Vitamin A RS in the Standard solution (μg/mL)

Change
Prepare a test solution containing the equivalent of 4 mg of amoxicillin per mL by adding 0.1 N hydrochloric acid to Amoxicillin for Injectable Suspension. Allow the solution to stand for 5 minutes before use: the solution responds to the Identification test under Amoxicillin Capsules.
to:
Prepare a test solution containing the equivalent of 4 mg of amoxicillin per mL by adding 0.1 N hydrochloric acid to Amoxicillin for Injectable Suspension. Allow the solution to stand for 5 minutes before use. Prepare a Standard solution of USP Amoxicillin RS in 0.1 N hydrochloric acid containing 4 mg per mL. Use within 10 minutes after preparation. Apply separately 5 µL of each solution on a thin-layer chromatographic plate coated with a 0.25-mm layer of chromatographic silica gel mixture (see Chromatography <621>). Place the plate in a suitable chromatographic chamber, and develop the chromatogram in a solvent system consisting of a mixture of methanol, chloroform, water, and pyridine (90:80:30:10). When the solvent front has moved about three-fourths of the length of the plate, remove the plate from the chamber, and dry with warm air for 10 minutes. Locate the spots on the plate by spraying lightly with a solution of ninhydrin in alcohol containing 3 mg per mL, and dry at 110° for 15 minutes: the R_F value of the principal spot obtained from the test solution corresponds to that obtained from the Standard solution.

In Procedure/System suitability/Suitability requirements: Change
Resolution: NLT 3 between telmisartan and telmisartan related compound A
Tailing factor: NMT 2.0 for the telmisartan peak
Capacity factor: NLT 1.5
Relative standard deviation: NMT 2.0%
to:
Resolution: NLT 3 between telmisartan and telmisartan related compound A
Tailing factor: NMT 2.0 for telmisartan
Relative standard deviation: NMT 2.0% for telmisartan

In Dissolution 〈711〉/Test 1/Analysis: Change
Determine the percentage of telmisartan (C₃₃H₃₀N₄O₂) dissolved:
Result = (A_U × C_S × V × 100)/(A_S × D × L)
to:
Calculate the percentage of the labeled amount of telmisartan (C₃₃H₃₀N₄O₂) dissolved:
Result = (A_U/A_S) × C_S × V × D × (1/L) × 100
AND
Change
C_S = concentration of the Standard solution (mg/mL)
to:
C_S = concentration of USP Telmisartan RS in the Standard solution (mg/mL)
AND
In Dissolution 〈711〉/Test 2/Analysis: Change
r_U = peak response from the Sample solution
r_S = peak response from the Standard solution
to:
r_U = peak response of telmisartan from the Sample solution
r_S = peak response of telmisartan from the Standard solution
AND
In Dissolution 〈711〉/Test 3/Analysis: Change
C_S = concentration of the Standard solution (mg/mL)
to:
C_S = concentration of USP Telmisartan RS in the Standard solution (mg/mL)

In Release Liner Peel Test: Change
The product fails the test if the mean peel force is outside the acceptable range determined during product development.
to:
The product fails the test if the overall mean peel force is outside the acceptable range determined during product development.

In Light-resistant container: Change
〈661.2〉, Functionality, Spectral Transmission Requirements for Light-Resistant Components and Systems.
to:
〈661.2〉, Functionality Test Method, Spectral Transmission Requirements for Light-Resistant Components and Systems.